• Q345R steel
  • 16Mo3 steel
  • A283GradeC steel
  • A516Grade70 steel
  • A572Grade50 steel
  • cortenA steel

Get Price And Support

SAE AISI 1035 (G10350) Carbon Steel :MakeItFrom

The graph bars on the material properties cards further below compare SAE AISI 1035 steel towrought carbon or non alloy steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half full

Inquiry

eFundaProperties of Stainless Steel AISI 1035

Properties Conditions T (°C) TreatmentDensity (×1000 kg/m 3) 7.7 8.0325 Poisson's Ratio0.27 0.3025 Elastic Modulus (GPa) 190 21025 Tensile Strength (Mpa) 485 25 cold drawn (round bar (50 75 mm)) moreYield Strength (Mpa) 415 Elongation (%) 10 Reduction in Area (%) 30 Hardness (HB) 143 25 cold drawn (round bar (50 75 mm)) more

Inquiry

AISI 1035 SAE UNS G10350 Carbon Steel Foundry

The chemical composition of AISI 1035 carbon steel is outlined in the following table. The physical properties of AISI 1035 carbon steel are tabulated below. The following table shows mechanical properties of AISI 1035 carbon steel. The thermal properties of AISI 1035

Inquiry

1035 ( AISI, ASTM, UNS) Worldwide equivalent grades

Chemical composition and properties of european equivalents (EN) for 1035 (USA, AISI, ASTM, UNS)C35 (1.0501) , C35R (1.1180) , C35E (1.1181) , 1035 (USA, AISI, ASTM, UNS ) European (EU, EN) and wordwide Steel equivalent grades. These comparison table is only intended as an indication of the closest khown equivalent grades.

Inquiry

Carbon Steel SAE/AISI 1035, Steel & Stainless Steel

By cold drawing 1035 round bar, it will increase the mechanical properties, improve the size tolerance and enhance the surface. In these conditions, 1035 steel bar may be used in a variety of tools, chain pins, sealing rings, nails, couplings, levers, studs, gears, bolts, rods,

Inquiry

AISI 1045 Steel, cold drawn, high temperature stress

Material NotesRespond to heat treatment, and flame and induction hardening, but not recommended for carburizing or cyaniding. Die forging and hot upsetting are good to excellent. Typical uses include gears, shafts, axles, bolts, studs, and machine parts. AISI cross reference for JIS S45C and KS SM45C.

Inquiry

Effect of Cooling Rate on the Microstructure and

The present investigation is aimed to study the effect of cooling rate after controlled hot forging on the microstructure and mechanical properties of medium carbon steel 35C8 (AISI 1035). The different mechanical properties like yield strength, ultimate tensile strength, percentage elongation, impact strength and hardness obtained are correlated with microstructure using high magnification optical microscope.

Inquiry

Investigating the Quality and Conformity of Carbon Steel

There are several properties that differentiates medium carbon steel AISI 1035 without alloying elements from high carbon and alloy steels. For instance it is more ductile, with higher degree of machinability and weldability compared to high carbon and alloy steels [12].

Inquiry

Effect of Cooling Rate on the Microstructure and

The present investigation is aimed to study the effect of cooling rate after controlled hot forging on the microstructure and mechanical properties of medium carbon steel 35C8 (AISI 1035). The different mechanical properties like yield strength, ultimate tensile strength, percentage elongation, impact strength and hardness obtained are correlated with microstructure using high magnification optical microscope.

Inquiry

Carbon Steel definition physical properties & heat treatment

Carbon steel is generally regarded as an iron carbon alloy with up to 1.7% carbon, less than 1.6% manganese, less than 0.6% silicon and less than 0.1% sulphur and phosphorus. However, CalQlata defines carbon steel as an iron carbon alloy with up to 1.7% carbon the mechanical properties of which are governed by its carbon content.

Inquiry

Effect of cutting parameters on surface residual stresses

Residual stresses (RSes) induced by turning processes have a great effect on the material properties of the machined components and their abilities to withstand severe loading conditions (creep, Effect of cutting parameters on surface residual stresses in dry turning of AISI 1035 alloy SpringerLink

Inquiry